Miniature Football Home  

Go Back   Miniature Electric Football Forums > RULES WORLD, RULES WORLD, RULES WORLD plus Strategies and Formations > Shootout Rules
FAQ Members List Calendar Mark Forums Read

Reply
 
Thread Tools Display Modes
  #1  
Old 01-07-2009, 01:22 AM
Michigan Joe's Avatar
Michigan Joe Michigan Joe is offline
MFCA MEMBER
 
Join Date: Dec 2006
Location: Mundelien, IL
Posts: 1,364
Default cover corner figure rule

Rule: cover corner hands no farther than 0.25" apart

Just wanted to ask about the eligability of the buzzball arms foreward figures as cover corners for the CBSMF league (and other shootout rules). I seem to remember them being used in the DFW but I noticed the arms of the hammer figure are actually closer to 0.5" apart than 0.25". This figure is a stock pose and is probably the most common corner used in many leagues across the country. The Lt. lockdown figure from buzzball has hands very near 0.25" apart. Are you going to allow this stock pose for corner? Do all custom corner poses have to meet the 0.25" rule or just have the hands within the width of the buzzball figure. Please confirm.
Thanks,
Joe
__________________
"Ask not what the MFCA can do for you, but what you can do for the MFCA"
Reply With Quote
  #2  
Old 01-07-2009, 04:27 AM
Reginald Rutledge's Avatar
Reginald Rutledge Reginald Rutledge is offline
MFCA MEMBER
 
Join Date: Dec 2006
Location: Arlington, Texas
Posts: 4,699
Default Any Cover Corner Figure...

must have the standard 0.25 inch separation of width. This is a standard that was established before the Buzzball corner was produced as it has been a standard in the Shootout Rules since the 1996 Shootout Championship.

If Buzzball corners were used with wider width ranges, it is because coaches were not called out on this and allowed the wider width.

It is not our intention to not allow any manufacturer's figure in the CBSMF but the guidelines should be followed. Therefore I would say unto you simply to re-heat the arms to come in to the standard 0.25 inch restriction and he should be okay.
Reply With Quote
  #3  
Old 01-07-2009, 02:31 PM
Michigan Joe's Avatar
Michigan Joe Michigan Joe is offline
MFCA MEMBER
 
Join Date: Dec 2006
Location: Mundelien, IL
Posts: 1,364
Default

thanks for the clarification.

For anyone who already may have these corners you can actually apply a little heat to the elbows and bend them in very easily (even after final painting). If the figure is alreayd painted, just use a couple of quick hits with the lighter on the elbow region of the arms.
__________________
"Ask not what the MFCA can do for you, but what you can do for the MFCA"
Reply With Quote
  #4  
Old 01-07-2009, 05:56 PM
Reginald Rutledge's Avatar
Reginald Rutledge Reginald Rutledge is offline
MFCA MEMBER
 
Join Date: Dec 2006
Location: Arlington, Texas
Posts: 4,699
Default Not a problem

One thing must be pointed out. You can use cover corners as Offensive linemen. However, on the defensive side of the ball, you can only have 2 cover corners out on the field at once.

Cover corners are defined as the two defensive backs with their hands outstretched towards the offensive player in a chucking position.

Reg
Reply With Quote
  #5  
Old 01-30-2009, 07:31 PM
Iron Eagle's Avatar
Iron Eagle Iron Eagle is offline
MFCA MEMBER
 
Join Date: Dec 2008
Location: Spring, TX
Posts: 111
Default

Is the Hammer Buzzball figure considered a cover corner? Can they be used on d-line?
__________________
"On the electric gridiron, the men aren't just separated from the boys... the boys become men and back again!" -Coach Iron Eagle (December 2008)
Reply With Quote
  #6  
Old 01-30-2009, 08:00 PM
The Rookie's Avatar
The Rookie The Rookie is offline
MFCA MEMBER
 
Join Date: Mar 2008
Location: Houston
Posts: 1,298
Default

The hammer figure is not a Cover corner
On the bottom of the buzz ball figures it says what they are
Hammer says OL
Cover corner says
CVR
Reply With Quote
  #7  
Old 03-08-2009, 03:54 PM
FrustratedFinFan FrustratedFinFan is offline
Coach
 
Join Date: Apr 2007
Location: California
Posts: 395
Default

I created some cover corners from Reggie's Hawk figure. I tested them out and they are great....but not knocking over figures like I saw happening when playing against them. What is the problem? Is it because I have the arms positioned wrong? I am using strong bases and testing them on my offense and they cover well, but rarely knock any receiver down. More often than not, they tangle up with the WR and hold or redirect him.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is On
Forum Jump

All times are GMT -4. The time now is 04:41 AM.

Powered by vBulletin Version 3.6.2
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.